Beckhoff CU8130-0240 страница 43 Скачать руководство пользователя

Страница: 43 / 57

Configuration

CU8130-0240

Version: 1.1

7.5.3

E_BatteryStatus

Battery status.

TYPE E_BatteryStatus :
(
    BatteryUnknownStatus,
    BatteryOk,
    BatteryReplace
);
END_TYPE

Name

Value

Meaning

BatteryUnknownStatus

The battery status is unknown.

BatteryOk

The battery status is OK.

BatteryReplace

The battery should be replaced.

Requirements

Development en-
vironment

Target platform

UPS hardware

PLC libraries to be
integrated (cate-
gory group)

TwinCAT v3.1.0

PC or CX (x86, x64, ARM)

• Beckhoff BAPI v1;

• Beckhoff P24Vxxxx;

• Beckhoff CP903x card (PCI/ISA);

• Beckhoff CX2100-09x4 models

(e.g. CX2100-0904 or
CX2100-0914 + "Smart Battery"
CX2900-0192);

• The APC devices that come

supplied with Beckhoff Industrial
PC support the Smart protocol
and can be configured with the
Windows UPS service.

Tc2_IoFunctions
(IO)

7.5.4

E_UpsCommStatus

Status of communication with the UPS hardware.

TYPE E_UpsCommStatus :
(
    UpsCommUnknownStatus,
    UpsCommOk,
    UpsCommFailed
);
END_TYPE

Name

Value

Meaning

UpsCommUnknownStatus

The communication status is
unknown.

UpsCommOk

Communication has been
established with the UPS.

UpsCommFailed

Communication with the UPS was
interrupted.

Содержание CU8130-0240


























































Результаты поиска

Содержание CU8130-0240

Отзывы:

Похожие инструкции для CU8130-0240

Бренды по названию

Популярные бренды

Beckhoff CU8130-0240, Руководство пользователя

Результаты поиска

Содержание CU8130-0240

Отзывы:

Похожие инструкции для CU8130-0240

Бренды по названию

Популярные бренды