manualshive.com logo in svg

Baroness LM315GG, Руководство по эксплуатации для владельца

Поделиться
Скачать
Baroness LM315GG Скачать руководство пользователя страница 68

Loosen the nut to adjust the length of the
spring.

A

1

i352yo-003

Engine Tension Belt_002

1

Nut

A

45.0 mm (1.772 in)

Lock it with the nut.

Adjustment of Parking Brake

Danger

Danger

If the brake wire is cut, the machine will be
unable to stop. This would be extremely
dangerous.
If the brake wire is cracked or damaged,
replace it with a new one immediately.
If the parking brake is not sufficiently effective
when you pull the parking brake lever, adjust
the brake wire.

Adjust the parking brake by tightening the brake
wire adjustment bolt.

1

2

4

3

ulabms-003

Adjustment of Parking Brake_001

1

Parking brake lever

2

Lock nut

3

Adjustment bolt

4

Brake wire

4.

5.

Adjusting Work Speed

Follow the steps below to make adjustments.

Turn "ON" the reel rotation switch.

1

B

A

mh4pyw-006

Adjusting Work Speed_001

1

Reel Rotation Switch

A

ON

B

OFF

Loosen the locknut on the side of the reel
rotation switch to adjust the length of the
bolt.

Length of the bolt (A) (Longer) : Slower
Length of the bolt (A) (Shorter) : Faster

Once the adjustment has completed, be sure
to lock with the nut.

1

A

cs6lrm-001

Adjusting Work Speed_002

1

Lock nut

A

Length of the bolt

1.

2.

･
･

LM315GC

Maintenance

Page 5-14

Maintenance (Main Body)

Содержание LM315GG












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды