manualshive.com logo in svg

Baroness LM315GG, Руководство по эксплуатации для владельца

Поделиться
Скачать
Baroness LM315GG Скачать руководство пользователя страница 62

Traveling pedal shaft fulcrum

8bq62b-160

Greasing Points_011

Rear wheel brake lever shaft

8bq62b-161

Greasing Points_012

Flexible wire edge
There is one greasing point on each flexible
wire.

8bq62b-151

Greasing Points_013

8.

9.

10.

Flexible wire
Use Moly speed grease No.2 and screw in
the grease cup 360 degrees to grease.

Add grease every 8 hours of operation.

8bq62b-162

Greasing Points_014

Add grease before operation.

8bq62b-163

Greasing Points_015

Maintenance (Mower)

Lapping of Reel Cutter (Cutting Cylinder)

Lapping is work similar to sharpening a cooking
knife. If the edges of the reel cutter (cutting
cylinder) and the bed knife (bottom blade)
become blunt and make cutting difficult, both the
reel cutter (cutting cylinder) and the bed knife
(bottom blade) should be simultaneously
sharpened by reversing the reel cutter (cutting
cylinder) with an abrasive paste applied.
However, lapping is a temporary measure and
would not restore the sharpness completely.
If the edges of the reel cutter (cutting cylinder)
and the bed knife (bottom blade) become blunt
and difficult to cut, follow the steps below to
perform lapping.

11.

LM315GC

Maintenance

Page 5-8

Maintenance (Mower)

Содержание LM315GG












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды