manualshive.com logo in svg

Barko 495B - SE, Руководство по обслуживанию

Поделиться
Скачать
Barko 495B - SE Скачать руководство пользователя страница 96

Service Manual

Last Updated - 9/28/2016

495B SE (S)

96

REMEDY

HYDRAULIC SYSTEM 

CONTINUED...

PROBLEM

CAUSE

No machine functions.

Low hydraulic oil level.

Plugged suction line.

Fill hydraulic reservoir with proper 

oil.

Clean or replace strainer.

REMEDY

CAUSE

PROBLEM

ELECTRICAL SYSTEM

Battery will not charge.

Loose or corroded connection.

Loose alternator belts.

Clean and tighten battery 

connections.

Tighten or replace belts.

Starter will not work or cranks 

slowly.

Loose or corroded connections.

Wrong engine oil.

Clean and tighten connections.

Replace engine oil.  Refer to Fuel 

and Lubricants.

Gauges do not work.

Gauge sender needs service.

Loose gauge ground connection.

Replace sender.

Check ground connection.  

Tighten if necessary.

Windshield Wiper/Washer does 

not work.

Defroster does not work.

Wiper/Washer switch needs 

service.

Wiper or washer motor needs 

service.

Disconnected or damaged wiring.

Replace switch.

Repair or replace motor.

Inspect wiring.  Connect or 

replace wiring as necessary.

Replace switch.

Repair or replace motor.

Inspect wiring.  Connect or 

replace wiring as necessary.

Defroster switch needs service.

Defroster fan motor needs 

service.

Disconnected or damaged wiring.

TROUBLE SHOOTING CONTINUED...

Содержание 495B - SE




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды