Barko 495B - SE Скачать руководство пользователя

Страница: 51 / 99

Service Manual

495B SE (S)

Last Updated - 9/28/2016

COLLECTOR TROUBLE SHOOTING CONTINUED...

11. Place the clean housing on a clean, firm work surface with the chamfer facing up.

12. Lightly oil the bore of the housing and the seals that are installed on the spool.

13. Install both wear rings.

14. Carefully place the spool into the chamfer. Gently (by hand) apply downward pressure on the spool until at least

the second seal is inserted into the bore. Using a plastic mallet, gently and slowly tap the spool into the housing

until it appears to be almost all the way home.

15. Then flip the entire collector over and tap on the housing (not the mounting ears) and the spool will extend out of

the housing approximately 1/8 of an inch.

NOTE: If a hydraulic press is available, it can be used in place of the plastic mallet.

16. Place the thrust washer around the spool, install the retaining plate and Loctite the cap screws in place.

17. Torque cap screws to 45 Ft. Lbs.

Содержание 495B - SE




































































































Результаты поиска

Содержание 495B - SE

Отзывы:

Похожие инструкции для 495B - SE

Бренды по названию

Популярные бренды

Barko 495B - SE, Руководство по обслуживанию

Результаты поиска

Содержание 495B - SE

Отзывы:

Похожие инструкции для 495B - SE

Бренды по названию

Популярные бренды