Barko 495B - SE страница 43 Скачать руководство пользователя

Страница: 43 / 99

Service Manual

495B SE (S)

Last Updated - 9/28/2016

HYDRAULIC FILTER MAINTENANCE CONTINUED...

5. Screw element on by hand until tight, to seat gasket in groove.

6. Loosen element.

7. Retighten element until it contacts gasket, then tighten 1/2 to 3/4 of a turn.

8. Check for leaks after start-up.

THE SERVO FILTER

(See Figure 3)

The servo filter has an indicator to show when filter needs servicing. Check indicator daily to ensure proper service

intervals.

CHANGING FILTER ELEMENT

1. Unscrew filter bowl from filter head.

2. Replace old element with new one inside filter bowl. Screw filter bowl with element inside to filter head.

These filter elements are not re-usable.

Figure 2

FILTER HEAD

GASKET

FILTER ELE-

MENT

FILTER ELEMENT REPLACEMENT INTERVALS

On new machine filter elements should be replaced after 50 hours of operation and then every 400 hours of operation

after that.

Содержание 495B - SE




































































































Результаты поиска

Содержание 495B - SE

Отзывы:

Похожие инструкции для 495B - SE

Бренды по названию

Популярные бренды

Barko 495B - SE, Руководство по обслуживанию

Результаты поиска

Содержание 495B - SE

Отзывы:

Похожие инструкции для 495B - SE

Бренды по названию

Популярные бренды