Barko 495B - SE Скачать руководство пользователя

Страница: 25 / 99

Service Manual

495B SE (S)

Last Updated - 9/28/2016

FUEL STORAGE

NOTE: Diesel fuels stored for a long time may form gum or bacteria and plug filters.

Keep fuel in a clean container and store in a protected area. Water and sediment must be removed before fuel gets

to the engine. Do not use de-icers to remove water from fuel. Do not depend on fuel filters to remove water.

NOTE: Keep all dirt, scale, water, or other foreign material out of fuel.

Store fuel drums on sides with plug up.

ALTERNATIVE LUBRICANTS

Conditions in certain geographical areas may require special lubricants and lubrication practices which do not appear

in this manual.

LUBRICANT STORAGE

The machine can operate at top efficiency only if clean lubricants are used. Use a clean container to handle all

lubricants. Store them in an area protected from dust, moisture, and other contaminants. Store drums on sides.

Diesel fuel or hydraulic fluid under pressure can penetrate the skin or eyes.

Fluid leaks under pressure may not be visible. Use a piece of cardboard or

wood to find leaks but do not use bare hand. Wear safety goggles. If fluid

enters skin or eyes, get immediate medical attention.

FLUID SPECIFICATIONS CONTINUED...

Содержание 495B - SE




































































































Результаты поиска

Содержание 495B - SE

Отзывы:

Похожие инструкции для 495B - SE

Бренды по названию

Популярные бренды

Barko 495B - SE, Руководство по обслуживанию

Результаты поиска

Содержание 495B - SE

Отзывы:

Похожие инструкции для 495B - SE

Бренды по названию

Популярные бренды