Barko 495B - SE Скачать руководство пользователя страница 8

Страница: 8 / 99

Service Manual

Last Updated - 9/28/2016

495B SE (S)

SAFETY SUMMARY

Combustible and flammable fluids can cause death or

severe injury. Do not smoke or permit open flames near

fuels or hydraulic fluids. Do not fill the tanks to capacity

- allow room for fluid expansion. Do not remove the

fuel cap or refuel while engine is hot, running or without

proper ventilation. Never use fuel for cleaning purposes.

Always lower boom to ground and shut down engine be-

fore leaving cab. If necessary to work on machine with

lifted boom, securely support machine and attachment.

Do not move loads over top of truck cab. Do not allow

driver to remain in truck cab while operating. Death,

severe injury or property damage may result.

Safe and stable mounting of this machine on a truck or

trailer bed is the owner's responsibility. See Mounting

Instructions for recommended procedures.

WARNING

When using a Slasher Saw Attachment, be sure to get

proper safety and operating manuals from Slasher

manufacturer. Read and understand those manuals

before using this machine for Slasher purposes.

Never approach power lines with any part of the ma-

chine. Current in a high voltage line may arc some dis-

tance to jump from the wire to a nearby "ground". KEEP

WELL CLEAR!

Do not operate machine during electrical storms.

Failure to fallow safety precautions in this manual can result in death, severe personal injury and/or property damage.

Carefully read safety precautions below and within this manual. Heed all decals on machine.

- Indicates an immediate hazard which WILL result in severe personal injury or death.

- Indicates a hazard or unsafe practice which COULD result in severe personal injury or death.

- Indicates a hazard or unsafe practice which could result in minor personal injury or property.

Содержание 495B - SE




































































































Результаты поиска

Содержание 495B - SE

Отзывы:

Бренды по названию

Популярные бренды

Barko 495B - SE, Руководство по обслуживанию

Результаты поиска

Содержание 495B - SE

Отзывы:

Бренды по названию

Популярные бренды