Barko 495B - SE страница 64 Скачать руководство пользователя

Страница: 64 / 99

Service Manual

Last Updated - 9/28/2016

495B SE (S)

Battery does not hold it's charge.

Alternator will not charge.

Starter will not turn the engine.

PROBLEM

CAUSE

1, 2, 3, 4, 5

1, 2, 5

2, 3, 4, 6, 7, 8

KEY TO CORRECT THE CAUSE

1. Alternator belt is loose or damaged.

2. Battery connections are dirty of loose.

3. Battery is damaged.

4. The ground connection is not making a good contact.

5. The alternator is damaged.

6. The engine is locked.

7. The starter has damage.

8. The wiring or the solenoid is damaged.

TROUBLE SHOOTING THE ELECTRICAL SYSTEM

The following trouble shooting chart is provided as an assistance in locating and correcting problems which are most

common.

ELECTRICAL SYSTEM MAINTENANCE CONTINUED...

Содержание 495B - SE




































































































Результаты поиска

Содержание 495B - SE

Отзывы:

Похожие инструкции для 495B - SE

Бренды по названию

Популярные бренды

Barko 495B - SE, Руководство по обслуживанию

Результаты поиска

Содержание 495B - SE

Отзывы:

Похожие инструкции для 495B - SE

Бренды по названию

Популярные бренды