Barko 495B - SE Скачать руководство пользователя

Страница: 5 / 99

Service Manual

495B SE (S)

Last Updated - 9/28/2016

ABBREVIATIONS AND SYMBOLS

EXPLANATIONS OF OTHER OCCURRENCES IN THIS MANUAL:

- In a parts list, when there are item numbers with empty spaces (no description or part number), these parts

have been previously deleted from that parts list and are not recorded anywhere.

- In a parts list, when there are items with no part number and a dotted line (----) is in the part number space,

this means that the part number is not sold separately or is not available at this time.

- When references to "right hand" or "left hand" are used in this manual, it is done from the operator's seat in

the forward operating position.

a/c

= air conditioner

= Articulated Carrier (Art. Car.)

adj.

= adjust or adjusting

appl.

= application

= As Required

assy

= assembly

= Back of Cab

b/m

= bill of material

brg.

= bearing

CAR

= Carrier

coll.

= collector

cond.

= conditioner

CRL

= Crawler

cyl.

= cylinder

dia.

= diameter

dwg.

= drawing

Ft. Lbs.

= Foot Pounds

gal.

= gallon

HRT

= Hydrostatic Rough Terrain carrier

ill. or illus. = illustration

In. Lbs.

= Inch Pounds

incl.

= includes or including

j.s.

= joystick

Lbs.

= pounds

LH (lh)

= left hand

mtg.

= mounting

N/A

= Not Applicable

no.

= number

NSS

= Not Sold Separately

opt.

= optional

pg.

= page

qt.

= quart

RH (rh)

= right hand

sec.

= secondary

see sep. ill. = see separate illustration (means:

located elsewhere in manual)

= Stationary Electric

SER or SR = Stationary Electric Remote

s/n

= serial number

str.

= straight

swhd

= saw head

= Truck Mount

= with

Содержание 495B - SE




































































































Результаты поиска

Содержание 495B - SE

Отзывы:

Похожие инструкции для 495B - SE

Бренды по названию

Популярные бренды

Barko 495B - SE, Руководство по обслуживанию

Результаты поиска

Содержание 495B - SE

Отзывы:

Похожие инструкции для 495B - SE

Бренды по названию

Популярные бренды