Barko 495B - SE Скачать руководство пользователя

Страница: 62 / 99

Service Manual

Last Updated - 9/28/2016

495B SE (S)

INSTALLING A NEW BATTERY

1. Remove battery cables. Remember position of positive terminal and negative terminal so you can connect them

again

correctly.

2. Remove battery hold-down bar. Remove battery from compartment.

3. Clean terminal posts of new battery and cable connections with wire brush.

4. Install new battery in compartment. Install hold-down bar.

5. Install and tighten battery cables. Connect negative cable last to prevent sparks.

Do not touch battery terminals with any metal. Sparks may occur,

causing damage to battery and personal injury.

ALTERNATOR DRIVE BELT ADJUSTMENT

1. Loosen alternator adjusting bolt and mounting bolt. See Figure 1.

2. Move alternator along adjustment bar to adjust tension of belt to

have 1/2" movement at 10 pounds of pressure at center of belt.

3. Tighten alternator adjusting bolt and mounting bolt.

After a new drive belt has been installed, it will be necessary to adjust

it after 8 hours of machine operation.

ALTERNATOR MAINTENANCE

CHECKING THE WIRING

1. Turn the starter switch on.

2. Connect a volt meter between the ground and: (See Figure 2.)

a) the No. 1 alternator connector.

b) the No. 2 alternator connector.

c) the "BAT" connector.

ELECTRICAL SYSTEM MAINTENANCE CONTINUED...

Содержание 495B - SE




































































































Результаты поиска

Содержание 495B - SE

Отзывы:

Похожие инструкции для 495B - SE

Бренды по названию

Популярные бренды

Barko 495B - SE, Руководство по обслуживанию

Результаты поиска

Содержание 495B - SE

Отзывы:

Похожие инструкции для 495B - SE

Бренды по названию

Популярные бренды