Barco DPMS Screen Saver
Single Source Master
108
amount of time it takes your display to warm up via the
“Monitor Setting” section. Contact your display vendor for
this warm-up time. On Barco C
ORONIS
displays, the I-GUARD
will stabilize the image within a few seconds after the
display returns to the active state, thus eliminating the need
for a warm-up period at the beginning of the work day.
9. If you wish to use this DPMS screen saver as the screen saver
at logon time, check the
“Use As Logon Screen Saver”
box
in the “Additional Options” section.
10. Save your preferences by pressing the
“Save As”
button and
entering a new profile name in the
“Save Profile Setting”
dialog box.
11. Apply your new scheme by clicking
“OK”
.
12. Click
“OK”
again to close the “Display Properties Control
Panel”.
Installing or Reinstalling Barco DPMS
To install or reinstall the Barco DPMS Screen Saver insert the
C
ORONIS
Software CD in the appropriate device on your computer
and run the BarcoMed Product Install Wizard (please see the
section Software Installation for complete instructions).
Special Note: Reinstalling the Barco DPMS Screen Saver will over
write the DPMS configuration settings and you will need to
reconfigure the DPMS settings on your system.
Uninstalling Barco DPMS
To remove the Barco DPMS Screen Saver from your system insert
the Coronis 1MP Software CD in the appropriate device on your
computer, run the BarcoMed Product Install Wizard and follow
these steps.
1. Select
only
the DPMS Screen Saver on the BarcoMed Product
Install Wizard’s welcome screen and click
“Install”
.
Содержание CORONIS 1MP
