Baoli KBET15 Скачать руководство пользователя

Страница: 98 / 100

In case of alarm follow this procedure:

1. program pump and drive DSP again; maybe software present in flash memory was

corrupted.

2. replace control board.

Alarm on 5 V encoder voltage

Eye alarm code: 37

Alarm level: 1

Alarm cause: Main board K1-14 terminal (5 V output) voltage is lower than 4.3 V.

In case of alarm follow this procedure:

1. verify if 5 V output is grounded, cause an incorrect encoder wiring.

2. verify if 5 V output is grounded, cause any encoder malfunction.

In that case, replace the defective one.

3. replace control board.

Alarm on 12 V output voltage

Eye alarm code: 38

Alarm level: 1

Alarm cause: Main board K1-12 terminal (12 V output) voltage is lower than 10.5 V.

In case of an alarm on 12 V output voltage, follow this procedure:

1. verify if 12 V output is grounded, cause an incorrect wiring to:

Accelerator potentiometer

Steering sensor

buzzer

display

2. replace defective device;

3. replace control board.

Содержание KBET15





































































































Результаты поиска

Содержание KBET15

Отзывы:

Похожие инструкции для KBET15

Бренды по названию

Популярные бренды

Baoli KBET15, Руководство оператора

Результаты поиска

Содержание KBET15

Отзывы:

Похожие инструкции для KBET15

Бренды по названию

Популярные бренды