Baoli KBET15 Скачать руководство пользователя

Страница: 99 / 100

Pump motor commands active on start

Eye alarm code: 50

Alarm level: warning; while the fault condition is active, all pump motor functions

(except hydro functions) are inhibited.

Alarm cause: you find a pump motor command active when you turn your system on.

In case of alarm follow this procedure:

1. before starting to operate, turn off any active command (both levers and switches);

2. be sure that lift, tilt and auxiliary command switches, are not active;

3. replace control board.

Seat switch open on start

Eye alarm code: 63

Alarm level: warning; main breaker is opened and pump and drive motors are stopped.

Alarm cause: when you start working, you find seat switch open, or, after the main

breaker is closed, the seat switch remains opened for at least “ seat switch delay” s.

In case of alarm follow this procedure:

1. verify if seat switch is defective;

2. replace control board.

Wrong start

Eye alarm code: 64

Alarm level: warning; main breaker is opened and pump and drive motors are stopped.

Alarm cause: when you start working, you find accelerator pedal pressed or a forward/

reverse switch active.

In case of alarm follow this procedure:

1. verify if a switch was active or the pedal pressed, when you turn on the lift truck;

2. verify if start, forward or reverse switches are stuck close;

3. verify if pedal circuit voltage exceeds 1/3 its maximum range (measured in Volt);

4. replace control board.

Содержание KBET15





































































































Результаты поиска

Содержание KBET15

Отзывы:

Похожие инструкции для KBET15

Бренды по названию

Популярные бренды

Baoli KBET15, Руководство оператора

Результаты поиска

Содержание KBET15

Отзывы:

Похожие инструкции для KBET15

Бренды по названию

Популярные бренды