Baoli KBET15 Скачать руководство пользователя

Страница: 86 / 100

Appendix A:

programmable parameters meaning

Programmable parameters

are here listed in functional groups.

The possibility of interfacing by PC with the system allows to have an exhaustive real time

analysis of the system working and of the condition of its components; moreover, you can

choose among a wide range of parameters in order to reach the optimum operating of the

system in compliance with your needs.

DRIVE MOTOR

PARAMETER NAME

Drive acceleration ramp

Lift truck acceleration with accelerator pedal pressed

Drive release ramp

Lift truck deceleration with accelerator pedal released

Drive inversion ramp

Lift truck deceleration in inversion

Pedal brake ramp

Lift truck deceleration with pedal brake pressed

Drive limitation maximum

speed

Maximum lift truck speed with speed limitation (turtle active)

Forward maximum speed

Maximum forward lift truck speed with no speed limitation
(no alarms present and turtle not active)

Reverse maximum speed

Maximum reverse lift truck speed with no speed limitation
(no alarms present and turtle not active)

Creep speed

If the truck speed is greater then this threshold, the speed reference
becomes a parabolic function of the accelerator potentiometer voltage.

Steer limitation maximum

speed

Maximum speed reference in the angle in which the internal wheel is
mechanically still.

Drive maximum current

Drive motors maximum current (expressed in per cent of high
energetic mode value)

Partial release ramp

Parameter that softens the drive inversion ramp if the traction motors
are working with low rpm

E-S-H enable

If this parameter is set to 1, it is possible to change the value of the
power
mode with the display

Slow speed

If parameter is set to1, speed limitation is active; otherwise lift truck
speed is managed as usual.

British unit

If parameter is set to 1, values are expressed in British unit, otherwise
in
international ones.

Time meter / odometer /

weight of the load on the

forks on display

If parameter value is 0, display shows the hour meter.
If parameter is set to 1, odometer indication appears .
If parameter value is 2, display shows weight on the forks .

DRIVE MOTOR

Содержание KBET15





































































































Результаты поиска

Содержание KBET15

Отзывы:

Похожие инструкции для KBET15

Бренды по названию

Популярные бренды

Baoli KBET15, Руководство оператора

Результаты поиска

Содержание KBET15

Отзывы:

Похожие инструкции для KBET15

Бренды по названию

Популярные бренды