Baoli KBET15 Скачать руководство пользователя страница 95

Страница: 95 / 100

In case of low battery alarm, follow this procedure:

1. measure battery voltage with a tester and, if different from the value reported on

COMPACT display, replace main board;

2. otherwise recharge battery.

Drive motor overtemperature

Eye alarm code: 13 for right drive motor

19 for left drive motor

Alarm level: 5

Alarm cause: The measure of drive motor temperature exceeds 155 ºC..

In case of alarm, follow this procedure:

Presence of alarm with cold motors:

1. with a handheld multimeter (in resistance operating mode) you have to measure a

resistance of about 10 kohm between the two wires of the temperature probe ( execute the

measure at ambient temperature of 25°C).

If the measure is not correct it is necessary to replace the temperature probe.

2. disconnect the temperature probe and check the wiring insulation between signal wire

and ground wire (towards control board);

3. replace control board.

Presence of alarm with hot motors:

1. If temperature value (you can read it from display or via PC) seems correct, verify if the

motor stator case are clean

Pump motor overtemperature

Eye alarm code: 14

Alarm level: 6

Alarm cause: The measure of pump motor temperature exceeds 155 ºC .

In case of alarm follow this procedure:

Presence of alarm with cold motors:

1. with a handheld multimeter in resistance operating mode, you have to measure about

10kohm at ambient temperature of 25°C between the two wires of the temperature

Содержание KBET15





































































































Результаты поиска

Содержание KBET15

Отзывы:

Похожие инструкции для KBET15

Бренды по названию

Популярные бренды

Baoli KBET15, Руководство оператора

Результаты поиска

Содержание KBET15

Отзывы:

Похожие инструкции для KBET15

Бренды по названию

Популярные бренды