Baoli KBET15 Скачать руководство пользователя

Страница: 96 / 100

probe. If the measure is not correct it is necessary to replace the temperature probe.

2. disconnect the temperature probe and check the wiring insulation between signal wire

and ground wire (towards control board);

3. replace control board.

Presence of alarm with hot motors:

1. If temperature value (you can read it from display or via PC) seems correct, verify if

the motor stator case are clean

Motor current offset alarm

Eye alarm code: 15 for right drive motor

16 for left drive motor

36 for pump motor

Alarm level: 1

Alarm cause: non-zero phase currents when you turn lift truck on.

In case of motor current offset alarm, follow this procedure:

1. replace the cable connecting the malfunctioning inverter to control board.

2. replace inverter.

3. replace main board.

Main breaker fault

Eye alarm code: 17

Alarm level: 1

Alarm cause: overcurrent on main breaker coil.

In case of alarm follow this procedure:

1. replace main breaker

2. replace control board .

Watchdog timer alarm

Eye alarm code: 18

Alarm level: 1

Содержание KBET15





































































































Результаты поиска

Содержание KBET15

Отзывы:

Похожие инструкции для KBET15

Бренды по названию

Популярные бренды

Baoli KBET15, Руководство оператора

Результаты поиска

Содержание KBET15

Отзывы:

Похожие инструкции для KBET15

Бренды по названию

Популярные бренды