B&R Automation Panel 5000 Скачать руководство пользователя страница 147

Страница: 147 / 216

Installation and wiring

Automation Panel 5000 User's manual V2.11

147

5.4 Removing the link module

The following requirements must be met:

•

All connected cables must be disconnected.

•

The Automation Panel must no longer be installed on the swing arm system.

1. Disconnect the power supply cable to the Automation Panel (disconnect the power cable). Disconnect from

all sources and poles!

2. Carry out electrostatic discharge at the ground connection.
3. Place the Automation Panel on a clean, flat surface.
4. Remove the Torx screws (T10) indicated in the following figure.

Figure 41: Removing the Torx screws

5. Pull firmly and evenly to remove the link module.

Figure 42: Removing the link module

6. The link module can now be replaced by following these steps in reverse order. The max. tightening torque

of the Torx screws (T10) is 0.5 Nm.

Содержание Automation Panel 5000

























































































































































































































Результаты поиска

Содержание Automation Panel 5000

Отзывы:

Похожие инструкции для Automation Panel 5000

Бренды по названию

Популярные бренды

B&R Automation Panel 5000, Руководство пользователя

Результаты поиска

Содержание Automation Panel 5000

Отзывы:

Похожие инструкции для Automation Panel 5000

Бренды по названию

Популярные бренды