Bandit
34
Copyright 8/19
MODEL SG-75
Inspect pockets, teeth and bolts for damage and
replace as required.
When replacing pockets, always replace new
pockets across from each other (180°) in order to
prevent vibration.
Replacement teeth must be carbide tipped and of
like design as provided with the machine.
To make sure the correct tooth pattern is used,
make sure a pocket with a locator pin is used on
a station with a locator pin hole. Use the pockets
without the locator pin on a station without the locator
pin hole.
When replacing complete set of teeth, be sure to
duplicate original factory tooth arrangement, with the
carbide tip facing the cutter wheel rotation. Typically
a 15/16” socket is required to change or torque the
teeth.Seepage29fortorquespecifications.
NEW RIVER “REVOLUTION” MAINTENANCE
MAINTENANCE
Inspect pockets, teeth and bolts for damage and
replace as required.
When replacing pockets, always replace new
pockets across from each other (180°) in order to
prevent vibration.
Replacement teeth must be carbide tipped and of
like design as provided with the machine.
Use anti-seize on threads to help prevent bolts
from “freezing up” in cutter wheel pockets.
When replacing complete set of teeth, be sure
to duplicate original factory tooth arrangement,
with the carbide tip facing the cutter wheel rotation.
Typically a 5/8” socket and a 3/4” socket are required
to change or torque the teeth. See page 29 for
torquespecifications.
GREEN TEETH MAINTENANCE
CUTTER WHEEL MAINTENANCE
DANGER
!
DANGER
!
DANGER
!
DANGER
!
Before attempting any type of maintenance,
disengage clutch or cutter wheel engagement, wait
for the cutter wheel to come to a complete stop,
position and lock the cutter wheel in the transport
position, turn off engine, remove the ignition key,
make sure the ignition key is in your possession,
disconnect the battery, and install the cutter wheel
lock pin.
DO NOT go near the rotating cutter head for any
reason. DO NOT go near the cutter head while the
engine is running or the cutter head is coasting to a
stop. Contact with a rotating cutter head will result
in serious bodily injury or death.
Never use hand on cutter wheel to hold in place
while changing teeth. Be sure to remove locking pin
before operating the machine.
DO NOT operate machine with extremely worn or
broken teeth.
WARNING
!
WARNING
!
DO NOT operate machine without a full set of
teeth. Operating the machine without a full set of
teeth can cause excessive vibration and premature
bearing failure.
Use only original equipment manufacturer’s teeth.
The use of any other aftermarket teeth may cause
damage or premature failure to the drive train.
NOTICE
A locking pin is provided to hold the cutter wheel
in position during tooth removal and reinstallation.
Locking pin will only lock on outer teeth.
See Page 49 for Cutter Wheel Setup & Part Numbers
See Page 48 for Cutter Wheel Setup & Part Numbers
Содержание SG-75
