background image

Bandit

28

Copyright 8/19

MODEL SG-75

MAINTENANCE

15. Check oil cooler: 

 

Thoroughly­ clean­ cooler­ fins­ at­ least­ once­ a­ day­

or more in excessive conditions. Make sure debris 

is­ not­ packed­ between­ fins.­ Use­ compressed­ air­

 

and/or pressurized water (soap may also be needed) 

to clean the oil cooler, depending on the level and 

type of debris. If pressurized water is used, be  careful 

not to turn the debris hard and pack solid  between 

the­cooler­fins.­Make­sure­to­clean­the­­cooler­in­the­

correct­direction;­do­not­propel­the­debris­into­the­

cooler with compressed air or  pressurized water. 

Keep the compressed air or pressurized water a 

safe­distance­from­the­cooler­fins­so­they­are­not­

damaged.­­Visually­inspect­the­cooler­fins­and­make­

sure­they­are­not­bent­or­closed­off,­repair­or­replace­

as needed. 

16. Check air cleaner and precleaner:

 

 

Clean or replace element following engine manual  

recommendations. Also, check and clean the 

 vacuator  valve.

17. Check machine controls: 

 

Operate all machine controls and ensure they  

operate smoothly and shift correctly.

18. Inspect, and adjust tracks: 

 

Check track tension, there must be no slack between 

the track rollers and the track rubber. For more 

detailed instructions, see page 35. Also, check 

tracks for wear, weather checking, and damage. 

Replace if damaged. 

19. Lubricate track expansion assembly: 

 

Apply dry lube to track expansion tubes daily.

20. Check around machine: 

 

Check around the entire machine for tools, cans, 

saws, etc. All tools not in use should be stored in 

a tool box.

21. Review all safety procedures on decals, from 

manual, and from video.
22. Make sure all safety equipment is being worn: 

Make sure you are wearing all of your safety 

 equipment: hard hat, face shield, gloves, eye 

 protection, ear  protection, etc. per ANSI and OSHA 

standards.

23. Remember to check EVERYTHING on the 

checklist.

10. Check hydraulic oil level: 

 

The hydraulic oil reservoir tank level should always  

remain at 7/8 full. Remember to check DAILY to avoid 

excessive heat build up.

11. 

Check for any fluid leaks: 

 

Inspect for any oil, fuel, hydraulic oil, or engine    

coolant­leaks.­Check­all­hoses,­fittings,­lines,­and­

tanks.­ DO­ NOT­ use­ fingers­ or­ skin­ to­ check­ for­

 hydraulic leaks. Repair or replace any damaged or 

leaking components.

12. Check the fuel level: 

 

Check the fuel level, running out and repriming is 

time­consuming.­Do­not­over­fill,­and­you­must­leave­

fuel expansion space in the top of the tank.

13. Check engine oil and coolant level:

 

 

F o l l o w   t h e   e n g i n e   m a n u f a c t u r e r   m a n u a l 

 recommendations for fluid levels. You MUST 

follow specific engine manufacturer’s manual 

recommendations for radiator coolant, additives, 

lubrication, correct engine speed, etc.

14. Check radiator, debris screen: 

 

Refer to the engine manufacturer’s manual. 

Thoroughly­clean­radiator­fins­at­least­once­a­day­

or more in excessive conditions. Make sure debris 

is­ not­ packed­ between­ fins.­ Use­ compressed­ air­

 

and/or pressurized water (soap may also be needed) 

to clean the radiator, depending on the level and type 

of debris. If pressurized water is used, be careful not 

to turn the debris hard and pack solid between the 

radiator­fins.­Make­sure­to­clean­the­radiator­in­the­

correct direction depending on if the cooling fan is 

a­sucker­or­a­pusher;­do­not­propel­the­debris­into­

the radiator with compressed air or pressurized 

water. A partially plugged radiator will not allow the 

engine to cool properly. Keep the compressed air or 

 pressurized water a safe distance from the  radiator 

fins so they are not damaged. Visually inspect 

the­radiator­fins­and­make­sure­they­are­not­bent­

or­ closed­ off,­ repair­ or­ replace­ as­ needed.­ Clean­

cooling fan, shroud on air cooled engines, and the 

debris screen (if so equipped). Improper service, 

maintenance, or neglect will cause overheating 

problems and/or engine failure.

DAILY START UP & MAINTENANCE (cont.)

1.  Lubricate all steel friction areas:

 

 

Lubricate all steel friction areas including, but not 

limited to pivoting, hinged, sliding, rotating areas 

on the machine (i.e. cutter wheel guard, control box 

doors, etc.).

2.  Check alternator and fan belts on engine (as 

applicable): 

 

Adjust and maintain per the engine manufacturer’s 

manual.

WEEKLY MAINTENANCE

Содержание SG-75





























































Отзывы: