Bandit Intimidator 12XP Скачать руководство пользователя страница 96

Страница: 96 / 108

BANDIT CONTROLS - CE

3/19

245840062970 8Oct2018

Push Button Feed Assist

Manual Winch with Push Button Feed Assist

There is a switch on the winch that sends a 12V signal to enable the winch valve. The winch stow switch

indicates to the control system whether the winch is stowed or deployed. The status of this switch is

displayed on Maint1 as shown above right.

When the Winch is deployed away from its stow point the Stow Switch energizes the winch selector valve and

now the winch can be operated using the manual winch control valve. While the winch is still out, the Feed

Assist Push Button can be used to enable Feed Fwd for approx 1/2 sec, then it will timeout and stop; this can

be repeated.

In order for the Feed Assist timer to work and allow oil during Feed Assist, the controller must see :

- a 4.99V (12V) signal from the Winch Out Switch

- a 10,000 (>500) signal from Fd Assist Switch

When the operator is finished with winch operations, the winch rope must be stowed properly to tighten

down on the Stow Bar. The Winch Out Switch will now indicate that the winch is no longer deployed and

normal chipper functions can resume feed fwd, etc.

The Yoke/Lift is disabled while winch is deployed. Except, Yoke/Lift can momentarily operate with Feed-

Assist-Fwd. Yoke/Lift is fully enabled again once the winch is properly stowed tight on the stow bar.

If the Feed Assist Switch is disconnected a 10,000 (>500) signal will be sent to the control system. The Feed

Assist will then time out and prevent Feeding until the switch is reconnected to ground for 0 (<500) signal.

Push Button Feed Assist Valve and Switch

Содержание Intimidator 12XP













































































































Результаты поиска

Содержание Intimidator 12XP

Отзывы:

Похожие инструкции для Intimidator 12XP

Бренды по названию

Популярные бренды

Bandit Intimidator 12XP, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание Intimidator 12XP

Отзывы:

Похожие инструкции для Intimidator 12XP

Бренды по названию

Популярные бренды