Bandit Intimidator 12XP Скачать руководство пользователя страница 35

Страница: 35 / 108

Bandit

MODEL 12XP CE

OPERATION

FEEDWHEEL STOP BAR

FEEDWHEEL ENGAGE BUTTONS

CONTROL OPERATING PROCEDURES

FEEDWHEEL TRAP DOOR

Before opening or closing the feedwheel

trap door: disengage clutch, wait for the drum

to come to a complete stop, turn off engine,

remove the ignition key, make sure the

ignition key is in your possession, install the

drum lock pin, and disconnect the battery. In the

event that dirty material is being run through the

chipper the feedwheel trap door can be opened.

YOKE LIFT CONTROL

The feedwheel stop bar will shut off the feedwheels

when activated. If the feedwheel stop bar is activated,

you will need to reactivate the feed system

The feedwheel engage buttons activate feed

forward and feed reverse. The green button toward

the discharge end will activate the feed forward.

The black button toward the infeed hopper end will

activate feed reverse.

The yoke lift control operates the top yoke lift

cylinder. To lower the yoke, push the yoke lift control

handle towards the discharge end of the machine.

To raise the yoke, push the yoke lift control handle

towards the infeed hopper of the machine. The yoke

lift control handle is in the flotation position when it

is in the center location.

SAFETY INSTRUCTIONS

Drive Side

CE-15 11/18

Feed

Reverse

Feed

Forward

CE-16 11/18

Radiator Side

Feed

Reverse

Feed

Forward

Содержание Intimidator 12XP













































































































Результаты поиска

Содержание Intimidator 12XP

Отзывы:

Похожие инструкции для Intimidator 12XP

Бренды по названию

Популярные бренды

Bandit Intimidator 12XP, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание Intimidator 12XP

Отзывы:

Похожие инструкции для Intimidator 12XP

Бренды по названию

Популярные бренды