Bandit Intimidator 12XP Скачать руководство пользователя страница 67

Страница: 67 / 108

Bandit

MODEL 12XP CE

HYDRAULICS

TYPICAL HYDRAULIC RELIEF

PRESSURE SETTINGS

TYPICAL HYDRAULIC FLOWS AND

RPM SETTINGS

(Approximate, For Reference Only,

Engine At Full RPM)

HYDRAULICS

Equipment

Model

12XP

Pump

LPM (GPM)

28.8 - 31.8

(7.6 - 8.4)

Top Feedwheel

LPM (GPM)

14.4 - 15.9

(3.8 - 4.2)

Bottom Feedwheel

LPM (GPM)

14.4 - 15.9

(3.8 - 4.2)

Feedwheel

RPM

57 - 64

Main Relief

bar (PSI)

172

(2500)

Feed Relief

bar (PSI)

172

(2500)

Yoke Relief

bar (PSI)

103

(1500)

Dinamic Winch Relief

bar (PSI)

(1250)

Discharge Rotate

bar (PSI)

(1200)

Discharge Flipper

bar (PSI)

(1000)

Do not under any circumstances over-set these

relief pressures, it will cause damage to component

parts and hydraulic parts.

These typical hydraulic flows and relief pressure

settings are with the engine at full RPM. All settings

are subject to change.

NOTICE

After the initial start-up of the machine and after

any replacement of hydraulic components, fittings

and hoses must be re-checked for leaks and

clearances.

THE BANDIT HYDRAULIC SYSTEM

The Bandit is equipped with a very efficient, simple

hydraulic system. Each component is capable of

withstanding a specified pressure and still operate

for a very long time.

• Avoid hydraulic pump cavitation. Low oil levels

or cold start-ups will cause the hydraulic pump to

cavitate. Cavitation will ruin the pump and possibly

the entire hydraulic system. Cavitation only has to

happen once. This will start the pump on its way to

ruin. Allow hydraulic system to turn slowly for several

minutes in cold weather in order for hydraulic system

to warm up. Cavitation is not covered under warranty.

• Do not increase the feedwheel relief valve settings

beyond specified pressure. This will cause damage to

hydraulic components. Do not set any other hydraulic

component past it’s specified pressure or this will

cause damage to the hydraulic components.

• Keep hydraulic oil clean. Dirty oil will cause

excessive wear and loss of hydraulic power.

•

Replace the hydraulic oil filter(s) after first 10 hours

and with each 400 hours of operation or 3 months.

• Replace hydraulic oil & suction screen(s) at least

once yearly. This is also a very good time to flush and

clean the tank. Replace hydraulic oil immediately if it is

contaminated or looks “milky”. See pages 51 - 52

for hydraulic oil requirements.

• If the Bandit’s hydraulic system is kept clean and

the hydraulic pressures are not increased beyond the

specified pressure, the maximum use and life should

be received from the Bandit chipper hydraulic system.

• If a problem is encountered, it will more than likely

be located in the relief valve or something as simple

as belts or clutch slipping, check these first.

•

Only use the optional adjustable flow control when

chipping large diameter trees. Do not leave the speed

adjustment partially open for long periods of time. This

will cause excessive heat to the hydraulic system!

Excessive heat will cause low feedwheel power and

premature failure of all hydraulic components. Always

operate system at full oil flow unless chipping large

diameter trees.

•

Do not close the optional hydraulic shut‑off valve

for more than 3 to 4 seconds. Hydraulic shut‑off

valve handle must be completely turned on (in line

with hose) at all times unless checking hydraulic

pressure. Pressure gauge should be safely stored and

installed only when checking pressure. Follow above

instructions or this will cause unwarranted damage to

the hydraulic components.

• Never close the ball valves on the hydraulic

tank suction ports (if equipped) while the machine

is running, this will ruin the hydraulic pump and

components.

•

Some component manufacturers require different

specific hydraulic lubrication, such as gear boxes,

undercarriage drives. Refer to their manuals and

maintenance section of this manual.

• After you have operated a new machine for

approximately an hour shut down the machine and

recheck all hydraulic fittings for tightness and leaks.

If the simple rules mentioned below are followed,

the hydraulic components will last for years:

Содержание Intimidator 12XP













































































































Результаты поиска

Содержание Intimidator 12XP

Отзывы:

Похожие инструкции для Intimidator 12XP

Бренды по названию

Популярные бренды

Bandit Intimidator 12XP, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание Intimidator 12XP

Отзывы:

Похожие инструкции для Intimidator 12XP

Бренды по названию

Популярные бренды