Bandit Intimidator 12XP Скачать руководство пользователя страница 97

Страница: 97 / 108

BANDIT CONTROLS - CE

Bandit

245840062970 8Oct2018

Electric Feed Assist

Electric Winch with Feed Assist

There is a switch on the winch that sends a 12V signal to enable the winch valve. The Winch Out Switch

indicates to the control system whether the winch is stowed or deployed and also provides voltage directly to

the winch control switches on the joystick. The status of the Winch Out Switch is displayed on Maint1 as

shown above right.

Electric Feed Assist is designed to operate both Feed and Winch functions at the same time but only for short

durations. When the Winch is deployed away from its stow point and the Winch valve is enabled, moving the

Feed Assist joystick to the right will also enable Feed Fwd for approx 1/2 sec, then it will timeout and stop; this

can be repeated.

In order for the Feed Assist timer to work and allow oil during Feed Assist, the controller must see :

- a 4.99V (12V) signal from the Winch Out Switch

- a 10,000 (>500) signal from Fd Assist Switch

When the operator is finished with winch operations, the winch rope must be stowed properly to tighten

down on the Stow Bar. The Winch Out Switch will remove voltage from the Winch control switches on the

joystick and also indicate that the winch is no longer deployed and normal chipper functions can resume feed

fwd, etc.

The Yoke/Lift is disabled while winch is deployed. Except, Yoke/Lift can momentarily operate with Feed-

Assist-Fwd. Yoke/Lift is fully enabled again once the winch is properly stowed tight on the stow bar.

If the Feed Assist Switch is disconnected a 10,000 (>500) signal will be sent to the control system. The Feed

Assist will then time out and prevent Feeding until the switch is reconnected to ground for 0 (<500) signal.

Winch In/Out,

Winch Feed FWD/REV

Содержание Intimidator 12XP













































































































Результаты поиска

Содержание Intimidator 12XP

Отзывы:

Похожие инструкции для Intimidator 12XP

Бренды по названию

Популярные бренды

Bandit Intimidator 12XP, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание Intimidator 12XP

Отзывы:

Похожие инструкции для Intimidator 12XP

Бренды по названию

Популярные бренды