Bad Boy 1025H Скачать руководство пользователя страница 102

Страница: 102 / 144

BAD BOY TRACTOR

▶

Alternating returning plowing

pattern

● This pattern is useful for narrow

or short fields or poorly planned

fields in which are not easy to turn.

● In the figure, the plowing width for

(1), (2), (3) and (4) should be over

lapped with the one for (5), (6) and

(7) for approx. 10 cm.

● For the sections (1) to (7), perform

plowing in an alternating pattern.

For the sections (8) to (19), plow

in a circular pattern.

● Refer to the sequential returning

pattern for other details.

Moving direction

Reverse driving

Finish

A: Border

Start

(9)

(13)

(17)

(19)(15)

(11)

(18)

(8)

(12)

(16)

(1)

(7)

(2)

(6)

(3)

(5)

(4)

(14)

(10)

● Turning:

1025H.indb 22

2021-07-06 오전 11:07:49

Содержание 1025H

















































































































































Результаты поиска

Содержание 1025H

Отзывы:

Похожие инструкции для 1025H

Бренды по названию

Популярные бренды

Bad Boy 1025H, Руководство оператора

Результаты поиска

Содержание 1025H

Отзывы:

Похожие инструкции для 1025H

Бренды по названию

Популярные бренды