Bad Boy 1025H Скачать руководство пользователя страница 89

Страница: 89 / 144

OPERATION

•

Getting off the tractor, make

the implement descend.

[Otherwise]

The implement descends itself,

and then causes some unex-

pected accident.

DANGER

of grease or oil. Never jump when

exiting machine. Never mount or

dismount a moving machine

RUNNING-IN PERIOD

▶

Within first 10 hours of operation



Inspect daily or every 10 hours



Tighten the wheel bolts

▶

After first 50 hours of operation



Tighten the wheel, disc and hub

bolts



Check the alternator and fan belt

tension as well as air inlet



Tighten the cooling system's

hose and clamp



Perform the scheduled 50-hour

maintenance

IMPORTANT

•

Always keep wheel bolts

tightened to prevent any

accident. Confirm that the

wheel bolts are tight before

operation. Check wheel bolt

torque at least twice within

the first 10 hours of operation,

check it periodically at every

50 hours thereafter. Change

the oil and filter after first 50

hours of operation.



Change the transmission/hy-

draulic oil and oil filter element



Change the engine oil and filter



Change the front axle fluid

1025H.indb 9

2021-07-06 오전 11:07:47

Содержание 1025H

















































































































































Результаты поиска

Содержание 1025H

Отзывы:

Бренды по названию

Популярные бренды

Bad Boy 1025H, Руководство оператора

Результаты поиска

Содержание 1025H

Отзывы:

Бренды по названию

Популярные бренды