Bad Boy 1025H Скачать руководство пользователя страница 31

Страница: 31 / 144

FOR YOUR SAFETY

Follow the instruction manual

when engaging an implement;

•

When engaging an implement

to the tractor, follow the in-

struction manual for the im-

plement.

If this instruction is ignored,

there is a risk of personal injury

or damage to the tractor.

WARNING

Pay attention to the balance be-

tween the front and rear side

during the front-end-loader op-

eration;

•

During the front-end-load-

er operation, apply weights

or implement to avoid loosing

balance between the front and

the rear side of tractor.

If this instruction is ignored,

there is a risk of overturning ac-

cident due to loss of balance.

WARNING

Balance a heavy implement with

weights;

•

When engaging a heavy imple-

ment, load the weights on the

front of tractor to keep the bal-

ance of the tractor.

If this instruction is ignored,

there is a risk of accident or in-

jury due to loss of balance.

WARNING

1025H.indb 25

2021-07-06 오전 11:07:39

Содержание 1025H

















































































































































Результаты поиска

Содержание 1025H

Отзывы:

Похожие инструкции для 1025H

Бренды по названию

Популярные бренды

Bad Boy 1025H, Руководство оператора

Результаты поиска

Содержание 1025H

Отзывы:

Похожие инструкции для 1025H

Бренды по названию

Популярные бренды