Bad Boy 1025H Скачать руководство пользователя страница 132

Страница: 132 / 144

BRANSON TRACTOR

Symptom

Inspection item

Action

6. The coolant warning

lamp is turned “ON”

during operation.



Is the coolant level in the reservoir tank low?



Refill the coolant.

7. The engine oil pres-

sure lamp is turned

“ON” during opera

tion.



Is the engine oil level low?



Refill the engine oil up to required level.



Is the viscosity of the engine oil low?



Replace the engine oil with proper viscosity.



Is the pressure switch defective?



Replace the switch.



Is the oil pump defective?



Contact the dealer for repair.

8. The battery charge

warning lamp is

turned “ON” during

operation.



Is the alternator defective?



Contact the dealer for repair.



Is the fan belt loosened or damaged?



Adjust the fan belt tension or replace it.

1025H.indb 4

2021-07-06 오전 11:07:52

Содержание 1025H

















































































































































Результаты поиска

Содержание 1025H

Отзывы:

Похожие инструкции для 1025H

Бренды по названию

Популярные бренды

Bad Boy 1025H, Руководство оператора

Результаты поиска

Содержание 1025H

Отзывы:

Похожие инструкции для 1025H

Бренды по названию

Популярные бренды