Bad Boy 1025H Скачать руководство пользователя страница 18

Страница: 18 / 144

BRANSON TRACTOR

Stop and cool down the engine

before fueling or lubricating;

•

Do not fill the fuel while the

engine is running or machine

is hot.

If this instruction is ignored, fuel

can catch fire or lead to fatal in

jury with burn.

DANGER

No fire or spark near to the bat

tery;

•

No fire or spark near to the

battery while checking and

charging the battery.

If this instruction is ignored, the

battery can cause a blaze or ex-

plosion and lead to a fatal injury

or death.

DANGER

Remove dirt and debris from

muffler and engine before oper

ating;

•

Clean if there is dust, debris

or fuel on the engine or muf-

fler before operating the ma-

chine every day.

If this instruction is ignored,

there is a risk of fire.

DANGER

1025H.indb 12

2021-07-06 오전 11:07:34

Содержание 1025H

















































































































































Результаты поиска

Содержание 1025H

Отзывы:

Похожие инструкции для 1025H

Бренды по названию

Популярные бренды

Bad Boy 1025H, Руководство оператора

Результаты поиска

Содержание 1025H

Отзывы:

Похожие инструкции для 1025H

Бренды по названию

Популярные бренды