Bad Boy 1025H Скачать руководство пользователя страница 19

Страница: 19 / 144

FOR YOUR SAFETY

ᇟቖ᝾#
⬖⃾Ṟᅶ$

Use a cor-

rect tool

㉆៪#ᇟጚ⨿#ⱞ▫
Ⱖᵆ#ᇟጚṦ#ᘍ⺪
Ẳ⟗⟆⬎1

Do not inflate the

tire bead max air

pressure

Use correct tools;

•

Use proper tools to carry out

all maintenance procedure.

Also have available the re-

quired tools in the tractor at

all times.

If this instruction is ignored,

there is a risk of accident due to

poor maintenance.

CAUTION

Check electrical component and

wire harness;

•

Check before work if the wire

harnesses are burned or stuck

on any other component, if the

cord cover is peeled off or if

the wire connectors are loose.

If this instruction is ignored, the

electrical short can cause fire

and injury.

WARNING

Do not over inflate tires;

•

When filling tires with air, do

not inflate it beyond the max

imum pressure stated in this

manual. (Refer to P5-22 of

Proper inflation pressure)

If this instruction is ignored, the

tire may blow out, causing an

injury.

CAUTION

1025H.indb 13

2021-07-06 오전 11:07:35

Содержание 1025H

















































































































































Результаты поиска

Содержание 1025H

Отзывы:

Похожие инструкции для 1025H

Бренды по названию

Популярные бренды

Bad Boy 1025H, Руководство оператора

Результаты поиска

Содержание 1025H

Отзывы:

Похожие инструкции для 1025H

Бренды по названию

Популярные бренды