manualshive.com logo in svg

Bad Boy 1025H, Руководство оператора

Поделиться
Скачать
Bad Boy 1025H Скачать руководство пользователя страница 134

7

-

6

BRANSON TRACTOR

Symptom

 Inspection item 

Action

1. The implement does not be lifted.

  Is the hydraulic flow control dial in the close 

position?

 

Adjust the hydraulic flow control dial.

 

Is the transmission oil level low?

 

Refill the transmission oil.

 

Is the air taken in the fluid suction system? 

  

Tighten the filter or connection parts. Re-

place the pipe or O-ring if damaged.

 

Is the oil filter clogged? 

 

Clean or replace it.

 

Is the Selective control valve lever in the de

-

tent position?

 

Put the Selective control valve lever in 

the neutral position.

 

Is the hydraulic pump defective? 

 

Contact the dealer for repair.

 

Is the cylinder damaged?

 

Contact the dealer for repair.

2. The implement does not be low

-

ered.

  

Is the hydraulic flow control dial in the close 

position?

 

Adjust the hydraulic flow control dial.

  

Is the position control lever on the lowest po

-

sition?

 

Move the position control lever.

 

The implement cannot be lowered even 

though the position control lever is placed in 

the lowest position.

 

Contact the dealer for repair.

TROUBLESHOOTING - HYDRAULIC SYSTEM

1025H.indb   6

1025H.indb   6

2021-07-06   오전 11:07:52

2021-07-06   오전 11:07:52

Содержание 1025H

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды