Bad Boy 1025H Скачать руководство пользователя страница 95

Страница: 95 / 144

OPERATION

DRIVING ON THE ROAD

•

When driving on a road or

crossing a dike, make sure to

connect the brake pedals. Oth-

erwise, the tractor may turn

abruptly or turn over due to

one-sided braking.

•

Observe the traffi c regulations

when driving on the road. Oth-

erwise, you may be involved

in an accident.

WARNING

•

This tractor is designed to ac-

commodate only one person. Do

not allow anyone on the tractor

other than the driver. Otherwise,

you will be exposed to a risk of

accident.

•

Put the PTO lever into “N” and

connect the brake pedals.

•

When making a turn, turn on the

direction indicator lamp to inform

other vehicles of your intention.

•

Pay particular cautions to narrow

farm roads, slopes, and grassy

shoulders, and reduce the speed.

•

Put the position control lever to

UP and lock it with the stopper.

Otherwise, you will be exposed

to a risk of an accident.

•

Connect the brake pedals when

driving on a road. Otherwise,

there is a risk of abrupt turning

or overturning due to one-sided

braking.

•

Before every operation, make

sure that operator wears safety

belt.

WARNING

ENTERING AND LEAVING THE

PAVEMENT

•

Make sure to connect the

brake pedal. Otherwise, the

tractor may turnover due to

one-sided braking.

WARNING

Keep implement

plement

low until rear

wheels are on

the pavement

Perpen-

dicular to

pavement!

Keep implement

low until rear

wheels are on

the pavement

1025H.indb 15

2021-07-06 오전 11:07:48

Содержание 1025H

















































































































































Результаты поиска

Содержание 1025H

Отзывы:

Похожие инструкции для 1025H

Бренды по названию

Популярные бренды

Bad Boy 1025H, Руководство оператора

Результаты поиска

Содержание 1025H

Отзывы:

Похожие инструкции для 1025H

Бренды по названию

Популярные бренды