Axis P1445-LE-3 Скачать руководство пользователя страница 58

Страница: 58 / 65

AXIS P1445-LE-3 License Plate Verifier Kit

Specifications

LED Indicators

Status LED

Indication

Unlit

Connection and normal operation.

Green

Steady green for 10 seconds for normal operation after startup completed.

Amber

Steady during startup. Flashes during firmware upgrade or reset to factory default.

Amber/Red

Flashes amber/red if network connection is unavailable or lost.

Red

Firmware upgrade failure.

SD card slot

NOTICE

TICE

• Risk of damage to SD card. Do not use sharp tools, metal objects, or excessive force when inserting or removing the

SD card. Use your fingers to insert and remove the card.

• Risk of data loss and corrupted recordings. Do not remove the SD card while the product is running. Unmount the SD card

from the product’s webpage before removal.

This product supports microSD/microSDHC/microSDXC cards.

For SD card recommendations, see

axis.com

microSD, microSDHC, and microSDXC Logos are trademarks of SD-3C LLC. microSD, microSDHC, microSDXC are

trademarks or registered trademarks of SD-3C, LLC in the United States, other countries or both.

Buttons

Control button

The control button is used for:

•

Resetting the product to factory default settings. See

Reset to factory default settings on page 63

Connectors

Network connector

RJ45 Ethernet connector with Power over Ethernet (PoE).

Audio connector

•

Audio in

– 3.5 mm input for a mono microphone, or a line-in mono signal (left channel is used from a stereo signal).

Audio input

Содержание P1445-LE-3


































































Результаты поиска

Содержание P1445-LE-3

Отзывы:

Похожие инструкции для P1445-LE-3

Бренды по названию

Популярные бренды

Axis P1445-LE-3, Руководство пользователя

Результаты поиска

Содержание P1445-LE-3

Отзывы:

Похожие инструкции для P1445-LE-3

Бренды по названию

Популярные бренды