Axis P1445-LE-3 Скачать руководство пользователя страница 19

Страница: 19 / 65

AXIS P1445-LE-3 License Plate Verifier Kit

Vehicle entry and exit scenario

To watch this video, go to the web version of this document.

www.axis.com/products/online-manual/45019#t10124267

Open a barrier for known vehicles using the camera's I/O

1. Go to the application’s webpage and select the

Event log

tab and add detected license plates to a list. See

Add detected

license plate to list on page 13

2. To edit the lists directly, go to the

List management

tab.

3. Enter the authorized license plate numbers in the

Allowlist

field.

4. Go to the

Settings

tab.

5. Under

Access control

, select the

Type

drop-down list, select

Internal I/O

6. Select the

I/O output #

7. In the

Barrier mode

drop-down list, select

Open from lists

and then check

Allowlist

8. In the

Vehicle direction

drop-down list, select

9. In the

ROI

drop-down-list, select the area of interest you would like to use, or if you would like to use all.

10. Check that the application identifies the license plate number in the allowlist as a known vehicle and that the barrier

opens as expected.

Note

You can change the name of any of the lists to fit your specific use case.

Get notified about an unauthorized vehicle

This example explains how to set up the application so that an event that triggers a notification can be created in the camera.

Requirements:

•

Basic setup done. See

Basic setup on page 4

1. Go to

List management

2. Enter the license plate number in the

Blocklist

field.

3. Go to the camera’s webpage.

4. Go to

Settings

Events

and set up an action rule with the application as a condition and with a notification as an action.

5. Check that the application identifies the added license plate number as an unauthorized vehicle and that the action

rule runs as expected.

Содержание P1445-LE-3


































































Результаты поиска

Содержание P1445-LE-3

Отзывы:

Похожие инструкции для P1445-LE-3

Бренды по названию

Популярные бренды

Axis P1445-LE-3, Руководство пользователя

Результаты поиска

Содержание P1445-LE-3

Отзывы:

Похожие инструкции для P1445-LE-3

Бренды по названию

Популярные бренды