Axis P1445-LE-3 Скачать руководство пользователя страница 4

Страница: 4 / 65

AXIS P1445-LE-3 License Plate Verifier Kit

Get started

These setup instructions are valid for cameras that are not sold as a kit with AXIS License Plate Verifier

Install the application on page 9

These setup instructions are valid for all scenarios:

Camera mounting recommendations on page 4

Step-by-step guide on page 6

Adjust the area of interest on page 10

Select region on page 11

Set up event storage on page 11

Camera mounting recommendations

•

When you select the mounting location, remember that direct sunlight can distort the image, for example, during sunrise
and sunset.

•

The mounting height for a camera in a

Access control

scenario should be half of the distance of that between the

vehicle and the camera.

•

The mounting height for camera in a

Free flow

(slow traffic license plate recognition) scenario should be less than half of

the distance of that between the vehicle and the camera.

Access control

capture distance: 2–7 m (6.6–23 ft). This example is based on the AXIS P3245–LVE-3 License Plate Verifier kit.

Capture distance: (x)

Mounting height (y)

2.0 m (6.6 ft)

1.0 m (3.3 ft)

3.0 m (9.8 ft)

1.5 m (4.9 ft)

Содержание P1445-LE-3


































































Результаты поиска

Содержание P1445-LE-3

Отзывы:

Похожие инструкции для P1445-LE-3

Бренды по названию

Популярные бренды

Axis P1445-LE-3, Руководство пользователя

Результаты поиска

Содержание P1445-LE-3

Отзывы:

Похожие инструкции для P1445-LE-3

Бренды по названию

Популярные бренды