Avaya CallPilot 600r Скачать руководство пользователя страница 97

Страница: 97 / 106

Result: The Avaya CallPilot Image Menu appears.

1. 600r server BIOS update

2. 600r FRU/SDR firmware update

3. 600r server Display Non-Default CMOS Settings

4. 600r server SSU

5. Reboot

6. Goto DOS

To upgrade or configure the BIOS

1. Enter 1 to run the 600r server BIOS update from the Avaya CallPilot Image Menu.

Result: The following message appears:

Enter Y to update the BIOS [Y,N]

2. Enter Y to confirm.

Result: The system displays the BIOS update progress and the following message

appears:

Update is now complete...

PLEASE POWER DOWN physically in order for the settings to take effect!

3. Power off your server by pressing the power button on the server faceplate, and

then power on the server by pressing the power button again.

Result: The system reboots and the Startup Menu appears.

4. Enter 3 to run Utilities (BIOS, Firmware, etc...) from the Startup Menu. If the Startup

Menu is not displayed, see

To display the Avaya CallPilot Image Menu

on page

96.

5. Enter 2 to run the 600r server FRU/SDR firmware update from the Avaya CallPilot

Image Menu.

Result: The following prompt appears: Enter Y to update the FRU,SDR [Y,N]

6. Enter Y to confirm.

Result: The system displays the FRU/SDR update progress and the following

message appears.

Update is now complete...

PLEASE POWER DOWN physically in order for the settings to take effect!

7. Power off your server by pressing the power button on the server faceplate, then

power on the server by pressing the power button again.

Result: The system reboots and the Startup Menu appears.

8. Remove the Image DVD from the DVD drive and enter any key.

Result: The system reboots.

9. The BIOS upgrade is complete.

Requirements for upgrading or reconfiguring the BIOS

Avaya CallPilot® 600r Server Maintenance and Diagnostics

December 2010 97

Содержание CallPilot 600r











































































































Результаты поиска

Содержание CallPilot 600r

Отзывы:

Avaya CallPilot 600r, Техническое обслуживание и диагностика, Страница: 97 / 106

Результаты поиска

Содержание CallPilot 600r

Отзывы: