manualshive.com logo in svg

Avaya CallPilot 600r, Техническое обслуживание и диагностика, Страница: 27 / 106

Поделиться
Скачать
Avaya CallPilot 600r Скачать руководство пользователя страница 27

The use of parts that are not supplied by Avaya can cause serious system problems or void

your Avaya warranty.

The following table shows a list of the current part numbers of field replacement units for the
600r at the time of publishing. Refer to the latest Avaya product catalog for any interim updates
to the part numbers.

Table 8: Field replacement units (FRUs)

Description of part

Part number

Hard disk drive mechanical tray

NTRH9205E5

External SCSI terminator

NTRH9244E6

Power supply

NTRH9245E5

Fanset

NTRH9246E5

Hard drive

NTRH9247E6

DDR memory (x2)

NTRH9224E5

DVDROM/CDRW combo

NTRH9232E5

What to do when the server fails to boot into service

This section suggests tasks you can perform to determine why the server fails the bootup cycle.

To determine why the server failed to boot to Windows

1. Try restarting the sever by pressing the power switch. Ensure the power cable for

the system monitor and the VGA cable are connected.

2. Listen for server-generated beep codes. Make note of any beep codes and contact

Avaya product support.

3. During the boot sequence, take note of the bootup POST messages
4. Refer to the Troubleshooting Guide (NN44200-700) for other suggestions. If you

still cannot determine the cause of the startup failure, call your Avaya technical

support representative.

To determine why CallPilot failed to come into service

If CallPilot failed to come into service, follow these steps:

1. Assuming the server loads Windows and you are able to log on, note any failed

MPB self-diagnostic failures when you log on to Windows.

2. Check the Windows Event Viewer for both Windows system errors and CallPilot

application errors. For instructions, see 

Viewing event logs

 on page 30.

What to do when the server fails to boot into service

Avaya CallPilot® 600r Server Maintenance and Diagnostics

December 2010     27

Содержание CallPilot 600r











































































































Отзывы:

Нет отзывов