Avaya CallPilot 600r Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 106

Avaya CallPilot 600r Скачать руководство пользователя страница 80

Figure 19: Hard disk drive location in carrier

11. With the black lever in the fully open position, slide the drive assembly into the

chassis. Insert the primary drive in the right bay. Ensure that the green latch at the

front of the drive carrier is to the right. Do not push on the black drive carrier lever

until the lever begins to close by itself.

12. When the black drive carrier lever begins to close by itself, push on it to lock the

drive assembly into place.

13. Take off the ESD strap.
14. Replace the front bezel.
15. Plug in the peripheral devices and Ethernet cables, connect the AC power cords,

and restart the server.

Replacing the front fan assembly

The front fan cooling assembly is not hot-swappable. You must power down the server and
disconnect the assembly from the power supply.

When to replace the cooling fan assembly

After one of the cooling fans is not turning, the other fan rotates faster to maintain the same
volume of air flow through the chassis. The hum of a cooling fan rotating faster is both louder
and higher in pitch than normal and indicates that the assembly must be replaced. You cannot
replace just one fan in the assembly.

Replacing basic chassis components

80 Avaya CallPilot® 600r Server Maintenance and Diagnostics

December 2010

«
...
78
79
80
81
82
...
»

Содержание CallPilot 600r











































































































Отзывы:

Нет отзывов