manualshive.com logo in svg

Avaya CallPilot 600r, Техническое обслуживание и диагностика, Страница: 78 / 106

Поделиться
Скачать
Avaya CallPilot 600r Скачать руководство пользователя страница 78

Figure 17: Removing the power supply

6. Lift the power supply from the chassis.
7. Insert the replacement power supply. Ensure that you insert the terminal block

through the hole in the rear of the chassis. Move any cables away from where the

power supply is inserted so that the cables are not pinched or damaged.

8. Plug the new power supply into the AC mains.
9. Lower the power supply into place. Ensure that the cables are not pinched under

the power supply. For more details, see 

Figure 17: Removing the power supply

 on

page 78.

10. Push firmly at the rear of the power supply to push the connector at the front of the

power supply into the power board.

11. Install the PCI riser assembly. For instructions, see 

Replacing the MPB96 card

 on

page 82.

12. Replace the connector cover over the completed connections.
13. Install the server cover. For instructions, see 

Removing and replacing the server

cover

 on page 74.

Replacing a hard drive

The 600r server has one SCSI drive. You do not need to remove the server cover to add or
replace a hard drive, but you must remove the front bezel.

 Important:

You must replace the hard drive with an identical unit or other Avaya-approved hard drive.

Replacing basic chassis components

78     Avaya CallPilot® 600r Server Maintenance and Diagnostics

December 2010

Содержание CallPilot 600r











































































































Отзывы:

Нет отзывов