Autonics PMC-1HS Series Скачать руководство пользователя страница 53

Страница: 53 / 82

6. Drive by Teaching Unit

© Copyright Reserved Autonics Co., Ltd.

①

Reset:

Resets the main body and the teaching unit�

②

X/Y display:

Displays the currently selected axis�

③

Register number display/dp:

Displays the currently selected register number when data is editing and

dp when drive handling�

④

Data display:

Displays the data of each register when data is editing and the current position of the

selected axis when drive is handling�

⑤

Input buttons

● X/Y: Converts the selecting axis. It is used to convert the sign of an input value when the value is

entered and a mode data that the mode data is entered�

●

REG: It is used to input the register number to display� If this button is pressed on the data input, the

data input is cancelled and returns to the state before the data input�

● ↑↓: Increases/decreases the displayed register number.

● EXC: Runs the displayed command. However, this command is only valid for ABS, INC, OUT, OTP and

HOM 1 to 4 commands.

●

DP: Converts the drive handling status and the data edit status�

●

WRT: Adds a value when data is editing�

⑥

Button display for drive operation

Displays button function as yellow letters to the left or the top of the input button in drive handling status�

The top end and the bottom end of the button handle X-axis and Y-axis respectively.

6.1

Operation of the data edit

The data edit includes input, display and change the operation mode/parameter or the operation program�
In data edit mode, a register number between 00 and 95 is displayed� In the drive handling mode, the REG

displays dp� Therefore, change into the drive edit mode by pressing the [DP] button�

Make sure that data edit should be done with communication speed 9,600 bps.

6.1.1

Register Selection

There are 00 to 95 registers on each axis .(except 64 to 70)

There are two ways to display registers�

①

Press [REG] button to input a register number as two digits�

Example: REG 04 ---- REG → 0 → 4

②

Press [↑] or [↓] button to change a register number.

If you give the button a short press, the number increases by one� Otherwise, the number increases

continuously�

If ABS and INC commands were configured in the register, the short press displays a position data and

the operation mode� If you press the button again, the next register is displayed�

The front of the teaching unit is as shown below;

②

④

①

③

⑥

⑤

Содержание PMC-1HS Series



















































































Результаты поиска

Содержание PMC-1HS Series

Отзывы:

Autonics PMC-1HS Series, Инструкция по эксплуатации, Страница: 53 / 82

Результаты поиска

Содержание PMC-1HS Series

Отзывы: