Autonics PMC-1HS Series Скачать руководство пользователя страница 35

Страница: 35 / 82

4. Configuration of Operation Program

© Copyright Reserved Autonics Co., Ltd.

4.2

Drive by Parallel I/F

Parallel I/F connector is CN3 on front panel of the body�
Refer to "8� Connector" for detailed description of I/O circuit or pin allocation for I/O signal�

This parallel interface is connected to a sequencer or mechanical junction to operate PMC-1HS/PMC- 2HS.

Each drive other than home search is selected by MODE0 and 1 (12 to 13) signals.

Drive

Operation

MODE1

MODE0

Home Search

Search home according to the home search mode configured.

Index

Execute the ABS and INC commands registered

by specifying register number�

OFF

JOG

Drive axes while input signal is On�

OFF

Continuous Drive Drive axes continuously�

OFF

Program Drive

Execute the operation program registered�

The ON state means the connection of input signal and GEX and the OFF state means the connected

signal is open� In addition, the ON/OFF state of output signal means that the transistor output of open

collector becomes ON/OFF and the number in parenthesis in the back of signal name means the relevant

pin number�

4.2.1

Home Search

After activating the axis specification signal (X: 4, Y: 5) of the axis to execute, the home search is executed

by activating the Home (2) input signal of more than 10 msec.
If the Home Search starts, nDRIVE/END (14 to 15) output signal of the running axis becomes ON. If the

Home Search ends, the signal goes to the OFF state. However, if the drive end pulse is enabled in Mode

tab, the nDRIVE/END output signal in the OFF state sends out ON pulse as much as the time of the drive

end pulse width (msec) set in Parameter tab at the end of the signal while the axis is searching Home.
Home search for only X-axis is as shown below.

Caution

●

During Auto Home Search, the soft limit is ignored even if it is enabled�

● For PMC-1HS, the axis specification signal is disabled.

● OFF signals of X and Y DRIVE/END are executed after OFF signal of the Home is confirmed.

HOME (CN3/2) input
X (CN3/4) input
Y (CN3/5) input
XDRIVE/END (CN3/14) output
YDRIVE/END (CN3/15) output

OFF
OFF
OFF
OFF
OFF

ON
ON

Min. 10 msec

ON (Drive starts)

Содержание PMC-1HS Series



















































































Результаты поиска

Содержание PMC-1HS Series

Отзывы:

Autonics PMC-1HS Series, Инструкция по эксплуатации, Страница: 35 / 82

Результаты поиска

Содержание PMC-1HS Series

Отзывы: