Autonics PMC-1HS Series Скачать руководство пользователя страница 38

Страница: 38 / 82

4. Configuration of Operation Program

© Copyright Reserved Autonics Co., Ltd.

4.2.4 Continuous

The continuous mode outputs drive pulses in + direction when the input signal RUN+ (6) is in ON state or in

- direction when the input signal RUN- (7) is in ON state. It outputs the drive pulse until the stop signal STOP

(11) goes to the ON state, in other words, the RUN signal of the drive is changed into the Stop signal (If the

Limit input in the proceeding direction is activated, the output stops).
The drive speed is configured as one of four drive speeds (from drive speed1 to 4) by the input signal SPD0

and 1 (8, 9). If the configuration of the drive speed is changed in driving, the speed is changed into the

changed speed at once�

Item specified

Input signal of CN3

Operation mode specification: Continuous mode MODE0 (12) = OFF, MODE1 (13) = ON
Axis specification

X (4), Y (5) = On state of the axis to execute

Drive Speed specification

SPD0 (8) to SPD1 (9)

Refer to "4.2.3 JOG" <Drive Speed configuration>.

4.2.5 Program

The program drive executes the operation program registered. The program drive is started by configuring

the following items as the input signal of Parallel I/F connector (CN3) when the drive start command, STOBE

(3) is in ON state.

Item specified

Input signal configuration to CN3

Operation mode: Index mode

MODE0 (12) = ON, MODE1 (13) = ON

Axis specification

X (4), Y (5) = ON state of the axis to execute

REGSL (6) to REGSL5 (11)

Refer to "4.2.2 Index" <Register number specification table> .

Содержание PMC-1HS Series



















































































Результаты поиска

Содержание PMC-1HS Series

Отзывы:

Autonics PMC-1HS Series, Инструкция по эксплуатации, Страница: 38 / 82

Результаты поиска

Содержание PMC-1HS Series

Отзывы: