manualshive.com logo in svg

Autonics PMC-1HS Series, Инструкция по эксплуатации, Страница: 49 / 82

Поделиться
Скачать
Autonics PMC-1HS Series Скачать руководство пользователя страница 49

5. Drive by PC

48

© Copyright Reserved Autonics Co., Ltd.

Input item

Command

Description

End P

ABS, INC, HOM

1: Output the end pulse after running the command

0: No-output after running the command

Caution  

For 1, the drive end pulse must be enabled in mode 

configuration.

Other command

Relative position

Both

ABS, INC and HOM on X-axis

Output port number: 0(OFF) / 1(ON)

Other command

Output port number: ON time (0 to 65,535 msec)

 

●

Reset: If the [Reset] button is pressed before the [Enter] button is pressed, the input data is reset and                  

the previous data is displayed�

Caution  After entering data, press the [Enter] button to update the program�

(1)  

File menu

The File (F) menu on the Program Edit screen has Save, Open commands for the operation program.

This menu has the same function with the File menu of the main screen�

(2)  

Edit menu

The Edit (E) menu of the Program Edit screen is listed as shown the table below.

Item

Function

Description

Cut

Clear of the selected area

Move the selected area to the clipboard. In online state, the program 

data of the changed register is added to the main body�

Copy

Copy of the selected area Copy the selected area to the clipboard�

Paste

Paste

Paste the selected area to the current register� In online state, the 

program data of the changed register is added to the main body�

Delete Deletion of lines

Delete the selected register in line unit� The register number after the 

deletion can be advanced� In online state, the program data after the 

deleted line is added to the main body�

Insert

Insertion of lines

Insert blanks to the selected line� If the last line number of the 

program after inserting blanks is over 63 with the numbers or more 

than 63 are deleted� In online state, the inserted program data is 

added to the main body�

Содержание PMC-1HS Series



















































































Отзывы:

Нет отзывов