Autonics PMC-1HS Series Скачать руководство пользователя страница 51

Страница: 51 / 82

5. Drive by PC

© Copyright Reserved Autonics Co., Ltd.

5.6

Error code

Errors listed in the table below are displayed at the bottom of the main screen�

Code

Error message

Description

208

SOFTWARE LIMIT + ERROR

Software LMT+ occurred.

209

SOFTWARE LIMIT - ERROR

Software LMT- occurred.

210

HARDWARE LIMIT + ERROR

nLMT+ signal is active level.

211

HARDWARE LIMIT - ERROR

nLMT- signal is active level.

212

ALARM ERROR

nALARM signal is activated by the Enable configuration.

213

EMG ERROR

EMG is low level (GEX connection).

214

PROGRAM ERROR

Program error

215

HOME ERROR

Home Search error of the main body

401

Break signal was received

The stop signal is received�

402

Frame error

403

Port Overrun error

Port overrun

404

Recive buffer Overflow

Receive buffer overflow

405

Parity error

406

Send buffer Full

Send buffer is full

407

Device control block of Port

was received

Unexpected error acquiring the device control block

(DCB) of a port

408

There is no response

No response for the command

501

X Axis is already driving now

X-axis was driven during the operation of X-axis

502

Y Axis is already driving now

Y-axis was driven during the operation of Y-axis

503

Please select Axis

Home Search and Index/Program was selected without

selecting any axis on the main screen�

504

Please input number from

0 to 63 for REG

A number other than 0 to 63 was inputted in REG

505

Please input number

Not specified value was input.

506

Please input number within

the limits

A value other than input range was input�

The online state can be changed into the offline state.
To recover the online state, select the File (F) and retry the communication such as Upload → Parameter →

X-axis.

Содержание PMC-1HS Series



















































































Результаты поиска

Содержание PMC-1HS Series

Отзывы:

Autonics PMC-1HS Series, Инструкция по эксплуатации, Страница: 51 / 82

Результаты поиска

Содержание PMC-1HS Series

Отзывы: