Autoglide CABRI-20P Скачать руководство пользователя

Страница: 26 / 29

INSTRUCTIONS CABRI-20P

Page 26

SWING GATE OPENER

B. Single Gate:

1 Master Gate Close

→

2 Master Gate Open

→

3 Master Gate Close

! Beware: The system learning process for single gate takes more than dual gate for
around 1 min, wait for the gate to complete the learning process.

4.6 Gate Operation

Press the button “A” on the transmitter for dual-gate operation.

Press the button “B” on the transmitter for single-gate operation in either single-gate or
dual-gate installation

4.7 Gate-moving Logic

(A) In gate-opening phase: The gates stop if the transmitter/push button is

activated, and close when the transmitter/push button is reactivated.

(B) In gate-closing phase: The gates stop if the transmitter/push button is activated,

and open when the transmitter/push button is reactivated.

encountering obstacles

4.8 Advanced Operation of the transmitter (SW3 Dip1/2 Remote1 &
Remote 2)

Содержание CABRI-20P






























Результаты поиска

Содержание CABRI-20P

Отзывы:

Похожие инструкции для CABRI-20P

Бренды по названию

Популярные бренды

Autoglide CABRI-20P, Руководство пользователя

Результаты поиска

Содержание CABRI-20P

Отзывы:

Похожие инструкции для CABRI-20P

Бренды по названию

Популярные бренды