background image

24

LKS 

- S2 24V DC

l

iability

We reserve the right to change or discontinue products at any time
without prior notice. Illustrations are subject to change. Although we take 
every care to ensure accuracy, we cannot accept liability for the content 
of this document.

The drives are demounted by reversing the steps, as for the installation. 
The adjustments are omitted.
1.   Completely disconnect the system from the power supply before
 

demounting a drive.

2.   After demounting a drive the window must be secured against in-
 

dependent opening.

Dispose of parts according to the locally applicable legal provisions.

w

aRRanty

 

anD

 C

uStomeR

 S

eRViCe

D

emounting

In principal apply our: 

„General Terms for the Supply of Products and Services of the 
German Electrical Industry (ZVEI)“.

The warranty corresponds with legal provisions and applies to the
country in which the product has been acquired.
The warranty includes material and manufacturing defects incurred
during normal use. 
The warranty period for delivered material is twelve months.
Warranty and liability claims for personal injuries or material damages 
are excluded, if caused by one or more of the following:
•  No proper incoming goods inspection.
•  Improper use of the product.
•  Improper installation, commissioning, operation, maintenance or
  repair of the product.
•  Operating the product by defect and improper installed or not
  functioning safety and protection devices.
•  Ignoring instructions and installation requirements in these in-
 structions.
•  Unauthorized constructional modifi cations at the product or
 accessories.
•  Disaster situations due to effects of foreign bodies and Acts of God.
•  Wear and tear.
Contact persons for possible warranty claims, for spare parts or
accessories are the employees of the responsible branch offi ce or the 
responsible person at

Firm 

a

UMÜlleR

 

a

UMatIc

 GmbH. 

Contact data are available at our homepage 

(www.aumueller-gmbh.de)

D

iSPoSal

According to the European Directive 2012/19 / EU on Waste Electrical 
and Electronic Equipment (WEEE) and its transposition into national law, 
obsolete electrical appliances must be collected separately and sent for 
environmentally friendly recycling.

D

isPosal

 / W

arranty

08

Содержание LKS S2 24V DC





























Отзывы: