manualshive.com logo in svg

AUMA ACExC 01.2 Intrusive, Руководство по эксплуатации

Поделиться
Скачать
AUMA ACExC 01.2 Intrusive Скачать руководство пользователя страница 92

Service conditions

Indoor and outdoor use permissible

Use

Any position

Mounting position

≤

 2 000 m above sea level

> 2,000 m above sea level, on request

Installation altitude

Refer to name plate of actuator controls

Ambient temperature

Up to 100 % relative humidity across the entire permissible temperature range

Humidity

IP68
Terminal compartment additionally sealed against interior of actuator controls (double sealed)

Enclosure protection in accordance
with IEC 60529

According to AUMA definition, enclosure protection IP68 meets the following requirements:

●

Depth of water: Maximum 8 m head of water

●

Continuous immersion in water: maximal 96 hours

●

Up to 10 operations during immersion

●

Modulating duty is not possible during immersion.

For exact version, refer to actuator controls name plate.

Pollution degree 4 (when closed), pollution degree 2 (internal)

Pollution degree according to
IEC 60664-1

1 g, from 10 Hz to 200 Hz
Resistant to vibration during start-up or for failures of the plant. However, a fatigue strength may not be
derived from this. (Not valid in combination with gearboxes)

Vibration resistance according to
IEC 60068-2-6

Suitable for use in areas with high salinity, almost permanent condensation, and
high pollution.

KS

Standard:

Corrosion protection

Suitable for use in areas with extremely high salinity, permanent condensation,
and high pollution.

KX

Option:

Double layer powder coating
Two-component iron-mica combination

Coating

AUMA silver-grey (similar to RAL 7037)

Standard:

Colour

Available colours on request

Option:

Accessories

For actuator controls mounted separately from the actuator, including plug/socket connector.
Connecting cable on request.
Recommended for high ambient temperatures, difficult access, or in case of heavy vibration during
service.
Cable length between actuator and actuator controls is max. 100 m. An MWG is required for position
feedback.

Wall bracket

AUMA CDT (Commissioning and Diagnostic Tool for Windows-based PC)
AUMA Assistant App (Commissioning and Diagnostic Tool)

Programming software

Further information

Approx. 12 kg (with AUMA KT Ex plug/socket connector)

Weight

ATEX Directive 2014/34/EU
Machinery Directive 2006/42/EC
Low Voltage Directive 2014/35/EU
EMC Directive 2014/30/EU
RoHS Directive 2011/65/EU

EU Directives

92

SAEx 07.2 – SAEx 16.2/SAREx 07.2 – SAREx 16.2 Control unit - electromechanical

Technical data

ACExC 01.2 Intrusive Profinet

Содержание ACExC 01.2 Intrusive









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды