manualshive.com logo in svg

AUMA ACExC 01.2 Intrusive, Руководство по эксплуатации

Поделиться
Скачать
AUMA ACExC 01.2 Intrusive Скачать руководство пользователя страница 68

5.

Perform setting in the second end position following the same steps.

6.

Approach both end positions again to check the setting.

→

If the measuring range cannot be set:
Refer to <Faults during commissioning>.

→

If the current values (0/4/20 mA) are incorrect:
Refer to <Current values: adjust>.

→

If the current value fluctuates (e.g. Between 4.0 – 4.2 mA):
Switch off LED end position signalling.
Refer to <LED end position signalling: switch on/off>.

11.1.2.

Current values : adjust

The current values (0/4/20 mA) set in end positions can be adjusted at any time.
Common values are e.g. 0.1 mA (instead of 0 mA) or 4.1 mA (instead 4 mA).

Information

If the current value fluctuates (e.g. between 4.0 – 4.2mA), the <LED end position
signalling> must be switched off for current adjustment.

→

Operate valve in desired end position (OPEN/CLOSED).

→

Reduce current value: Press push button [S1]
(the current is reduced by 0.02 mA every time the push button is
pressed)

→

Increase current value: Press push button [S2]
(the current is increased by 0.02 mA every time the push button is
pressed)

11.1.3.

LED end position signalling: switch on/off

The LED behaviour for end position reached can be set as follows: blinking/continuous
illumination or no illumination. During setting mode, end position signalling is switched
on.

Switching on and off

1.

Operate valve in one of the end positions (OPEN/CLOSED).

2.

Hold down push buttons [S1] or [S2] for approx. 3 seconds.

➥

End position signalling is switched on or off.

Table 30:

LED behaviour when end position signalling is switched on

LED behaviour in end position

Set output current

 LED is blinking slowly

4 mA

 LED is blinking fast

0 mA

 LED is illuminated

20 mA

11.2.

Potentiometer

The potentiometer is used as travel sensor and records the valve position.

Setting elements

The potentiometer is housed in the actuator switch compartment. The switch
compartment must be opened to perform any settings. Refer to <Switch compartment:
open>.

Setting is made via potentiometer [1].

68

SAEx 07.2 – SAEx 16.2/SAREx 07.2 – SAREx 16.2 Control unit - electromechanical

Commissioning (optional equipment settings)

ACExC 01.2 Intrusive Profinet

Содержание ACExC 01.2 Intrusive









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды