AUMA ACExC 01.2 Intrusive Скачать руководство пользователя страница 54

Страница: 54 / 104

Indication light 2

Torque fault CLOSE

Indication light 3

Thermal fault

Indication light 4

Torque fault OPEN

Indicat. light 5 (right)

End p. OPEN, blink

Signal interm. pos.

OPEN/CLOSED = Off

Further setting values:

Refer to Manual (Operation and setting).

8.4.

Optional indications

8.4.1.

Mechanical position indication via indicator mark

Figure 63: Mechanical position indicator

[1]

End position OPEN reached

[2]

End position CLOSED reached

[3]

Indicator mark at cover

Characteristics

●

Independent of power supply

●

Used as running indication: Indicator disc rotates during actuator operation and
continuously indicates the valve position

(For “clockwise closing ” version, the symbols

rotate in counterclockwise

direction for operations in direction CLOSE)

●

Indicates that end positions (OPEN/CLOSED) have been reached

(Symbols

(OPEN)/

(CLOSED) point to the indicator mark at cover)

SAEx 07.2 – SAEx 16.2/SAREx 07.2 – SAREx 16.2 Control unit - electromechanical

Indications

ACExC 01.2 Intrusive Profinet

Содержание ACExC 01.2 Intrusive









































































































Результаты поиска

Содержание ACExC 01.2 Intrusive

Отзывы:

Бренды по названию

Популярные бренды

AUMA ACExC 01.2 Intrusive, Руководство по эксплуатации

Результаты поиска

Содержание ACExC 01.2 Intrusive

Отзывы:

Бренды по названию

Популярные бренды