AUMA ACExC 01.2 Intrusive Скачать руководство пользователя страница 32

Страница: 32 / 104

Figure 26: Disassembly of mounting frame

[1]

Screws

[2]

Mounting frame with connection board

Loosen screws [1] and remove mounting frame [2].

How to proceed

Remove cable sheathing in a length of 250 – 300 mm.

Insert the wires into the cable glands.

Fasten cable glands with the specified torque to ensure required enclosure
protection.

Information: For shielded cables: Link the cable shield end via the cable gland
to the housing (earthing).

Strip wires:

5.1 Remove wire sheathing of control cables (1...50) in a length of approx. 10

5.2 Remove wire sheathing of motor cables (U,V,W) in a length of approx.

12 mm

For flexible cables: Use wire end sleeves according to DIN 46228. For spring
clamp terminals, connection is also possible without wire end sleeves.

Information: For two flexible wires per terminal, a joint wire end sleeve must
be used (twin wire end sleeve).

SAEx 07.2 – SAEx 16.2/SAREx 07.2 – SAREx 16.2 Control unit - electromechanical

Electrical connection

ACExC 01.2 Intrusive Profinet

Содержание ACExC 01.2 Intrusive









































































































Результаты поиска

Содержание ACExC 01.2 Intrusive

Отзывы:

Бренды по названию

Популярные бренды

AUMA ACExC 01.2 Intrusive, Руководство по эксплуатации

Результаты поиска

Содержание ACExC 01.2 Intrusive

Отзывы:

Бренды по названию

Популярные бренды